Did you know?

You can make your own "rod-and-ring" system: the rod is a length (about 12-16") of 1/2" galvanized pipe; you hammerdirill a 7/8" hole down thru the concrete, and a matching hole, centered, up into the bottom of the post, about 4-6" deep. The rod slips into these holes.How to install concrete strike anchors. http://www.confast.com/products/concrete-strike-anchor.aspxThese hardware and fastener options are as much about lateral loads and uplift as they are about solid bearing surfaces.Watch the entire 10-part video series...

Tie a sail to a boat and the wind will move it around the world. With the wind and dust storms we get here, sails create a LOT of torque. A simple hollow wall won't provide sufficient anchorage. The standard response to this is to build spanner plates and attach them to the wall and fill the wall's cells with concrete so there's a solid piece.Secure Mount Post. Install railing directly onto a deck without using wood posts. The versatile Secure-Mount Post can be installed onto composite decks or concrete surfaces and adjusted to the exact height you need. Use with the Deck Mounting and Leveling Kit. The 6-inch adjustable top block allows for quick, easy extension from 36″ to 42″.By following these steps and using the right tools, you can secure your attachment to a concrete patio with confidence. Whether you drill holes or use anchors, attention to detail is key for a strong and durable connection. Attaching the 4×4 Post Attaching the 4×4 Post: Ensuring Stability and Alignment ...1 post · Joined 2010. #1 · Aug 20, 2010. I have an existing porch that I want to remove the 4x4 post, sleeve them with a vinyl sleeve and remount.Can I use a standard post mount secured to the concrete?I do not see how you can screw the sides of the post mount to the 4x4 post when using a vinyl sleeve? How do I mount the top to the header ...Pour in Concrete. After you’ve got your aggregate in, it’s time to pour in the concrete. Concrete should be 2-3 inches above the soil level. This gives you the ability to shape the concrete around the fence post base a bit. Trowel the top smooth and slope it so that water runs away from the post. You don’t want water to have an ...

37507 posts · Joined 2011. #3 · Oct 4, 2014. Any Simpson post base is going to flex if you try and just attach it on top of that concrete. Far better to dig a hole next to it and set the post in concrete. When posting in forums, letting us know your location will help others give better feedback/advice/solutions to your questions.Step 1. Measure the width of the privacy screen, or the distance from one side to the other, and record it. Also measure the height of the screen. Depending on its width, you need enough lengths of rebar, stakes or iron rods that match the height of the screen and are spaced every 24 inches apart along its span. Video of the Day. ….

Reader Q&A - also see RECOMMENDED ARTICLES & FAQs. How to secure a 4x4 to concrete. Possible cause: Not clear how to secure a 4x4 to concrete.

Either grind the concrete flat right at the corner of the top step or move the post in, away from the bulge around the current pipes. To avoid having to deal with the mound of concrete entirely, and to avoid cutting the 4x4 post, you could put the entire 4x4 post on the "outside" of the steps, like this:We can send men to the moon but still seem to have not worked out how to ensure fences stay vertical!!! Watch me as I fix my fence post that really doesn't w...If you want to help support Shannon to produce more videos like this, visit https://www.house-improvements.com/donateShannon from https://www.house-improveme...

Tap out any air bubbles from the adhesive. Place and press the pressure treated wood on concrete aligning to the line on the concrete. Use a wedge to compress the bottom plate or edge to the concrete. Leave to dry, curing for 8-24 hours. The longer it sits, the more bonding it will provide.First, drill holes through the wood sole plate with a wood bit and mark the floor. Move the sole plate, drill the floor, suck out the dust, and tap the shield into place. Replace the sole plate and drive lag screws with washers into the shields. 7. Hammer-Drive Anchor.

hobby lobby christmas gifts 4. Drill a pilot hole through each table leg's center unless you have pre-installed hanger bolts. Turn the table legs so the top portion, meant to connect to the table, faces you. Then, use a power drill to create the pilot hole down through the center. The pilot holes will prevent the wood from cracking later.3. Use a 2x4 to tamp the earth around each post. 4. Fill the hole about 1/3 full of gravel, and tamp the gravel down. Fill the rest of the hole with a special no-mix concrete designed for use in postholes. Continue until each posthole is filled. 5. Mist the concrete with water and use a trowel to press concrete around posts. How much water you ... delta airlines 2077tyree sampson With just a couple of brackets and some masonry screws, you can take care of this in just an afternoon.Subscribe to Today's Homeowner for more great home imp...To attach a ledger against a wall through brick veneer: Mark anchor locations on your ledger and drill through the board with a ½" bit. Position the ledger against the wall and mark the anchor positions through the hole onto the wall. Drill through the brick veneer with a ½ inch masonry bit in a hammer drill, until you reach the wood frame ... acme freshmarket Post-to-Concrete (page 11) Joist-to-Beam (page 14) A system of key connections throughout the deck framing, also known as a continuous load path, is essential to building a safe, code-compliant deck. When this system of connections is made properly, loads are transferredNext, we grabbed eight foot 4x4's for each planter. The quick set cement set really fast -- but this next step was helpful. I installed "L" brackets onto the bottom of each 4x4 and then screwed them into the bottom of the planters before adding the cement: ... This way you can secure the wire first and then add the lights after the fact. I ... craigslist flagstaff toolshappy nails hilton headwhat happened on 10 freeway today Procedure. To set fence posts in sand, simply dig a hole that's slightly larger than your post. Fill the hole with sand, and then use a level to make sure the post is straight. Once the post is in place, you can backfill the hole with additional sand. This method is quick and easy, and it's a great option if you're installing a taller fence. holyland halal meat grocery Check Out Our FREE GUIDE: *25 Must-Have Carpentry Tools...Under $25 Each!*https://www.thehonestcarpenter.com/AFFILIATE TOOL LINKS:Swanson Post Level:https://...If you choose a hammer-set concrete fastener instead, ensure that you make a mark on the board and drill right into the middle of it. Clear the hole using a vacuum or syringe blower. When drilling, ensure you create a hole that passes through the entire wood so you can access the concrete easily. Step 2: Nailing Mortal Nails through Wood to ... daniel boone pellet grill manualhot topic fairbanks akfirst alert green light It is supported by four 4X4 posts, about 8' or 9' high. One post had to be removed because of dry rot and termite damage. When I removed it it did not seemed attached to the concrete walkway at all. How does one attached a post to a concrete walkway? I have experience with attaching wood to wood, but none with wood to concrete.