Netgear cm1000 setup

Buy NETGEAR Cable Modem CM1000 - Compatible with All Cable Providers Including Xfinity by Comcast, Spectrum, Cox | for Cable Plans Up to 1 Gigabit | DOCSIS 3.1, Black (CM1000-1AZNAS): Modems - Amazon.com FREE DELIVERY possible on eligible purchases

Jan 23, 2022 · Check your coax for kinks, damage, loose/old/bad/cheap connectors and remove them if you do. Preferrably, directly connect the modem to where the coax line enters the home. This prevents wiring within the home from being the issue. Current setup: CM2000-> RBKE963B-> Trendnet TEG-S380-> GS716T-> pi-hole. Hello all. I upgraded to the Gigabit plan with Xfinity. I use my own Modem (Arris Surfboard 3.0). After realizing I needed a Docsis 3.1 I bought the Motorola MB8600 or whatever but it was 3.1. Comcast couldn't get it to keep a signal. The modem kept rebooting over and over. Comcast tech came to my house and said I had a defective modem as his ...Have the ISP check the signal and line quality UP to the modem. Connect a wired PC to the back of the modem with out the router in the middle, power OFF the modem for 1 minute then back on. Check for internet services and speed. My Setup | ISP SparkLight | Internet Cable 1000↓/50↑ CAX80 Modem Mode | Wifi Router RBE973S and SXK30; Router ...Model: CM1000|Ultra-High Speed Cable Modem—DOCSIS® 3.1 Ready, R8000|Nighthawk X6 AC3200 Smart WIFI Router, R8000P|Nighthawk X6S AC4000 Tri Band WiFi RouterCurrent setup: CM2000-> RBKE963B-> Trendnet TEG-S380-> GS716T-> pi-hole also in AP setup: RAXE500->EAX80 1.4gig download/50mbps upload from Xfinity We're members of the public helping out on our own time.This is a review of the Netgear Nighthawk Ultra-High Speed Cable Modem CM1000. The Netgear Nighthawk Ultra-High Speed Cable Modem CM1000 is a 1Gbps capable m...

Place your extender in the same room as your WiFi router. Proximity to the WiFi router is required only during the initial setup process. Plug the extender into an electrical outlet. Wait for the Power LED to light green. If the Power LED does not light, press the Power On/Off button on the side of the extender.Activation and Installation. During the initial setup of your cable modem, you must contact your Internet service provider (ISP) to activate your device. Your ISP verifies your modem's MAC address and that your Internet service is active. How do I activate Internet service on my NETGEAR cable modem or modem router?Solved: Spectrum in my area finally added the first DOCSIS 3.1 modem cm1000 v2 to there compatibility list. Searching cm1000 in online stores does × We are aware of an issue affecting Nighthawk CAX30 Cable Modem Routers that may have resulted in an interruption of internet service.CS of 10 is similar to a 4.8 star review, CS of 0 is similar to a 2 star review. Netgear CM1000, the cheaper option, tends to get more favorable reviews than Arris Surfboard S33. As can be seen in the chart above, median best-selling modem receives a consumer score of 7.4 (good). Both Arris Surfboard S33 and Netgear CM1000 receive customer ...NETGEAR-Guest is for the 2.4 GHz WiFi band. NETGEAR-5G-Guest is for the 5 GHz WiFi band. Ensure that the Enable SSID Broadcast check box selected. Allowing the router to broadcast its WiFi network name (SSID) makes it easier to find your network and connect to it. If you clear this check box, you create a hidden network. Enter a guest …Netgear Nighthawk CM1200 Modem: https://amzn.to/3buAehFFirst impressions:Slick looking high speed modem. It dramatically improved my internet speed more th...Page Setup is a group of options dictating the way a document is formatted to print. These include margins, page orientation, size and quality of print. To access the page setup di...

Netgear CM1000 DOCSIS 3.1 Ultra High Speed Gigabit Cable Modem. MODEL: CM1000100NAS MPN: CM1000-100NAS. (0) Write a review. View all Netgear Modems. $229.99.A single point of support around the clock. Premium Support makes it easy to fix issues on not just your NETGEAR purchase but for your entire home network. The service includes support for the following: NETGEAR and non-NETGEAR network devices. Desktop and Notebook PCs, Printers, Scanners, and more. Windows Operating Systems, MS Office, Outlook ...1. Hide TV wires/cords/cables https://youtu.be/fpZ5Sc6CLYA2. Damaged FLOATING Entertainment Center https://youtu.be/O5Zwkj3JycQ3. Google ...With NETGEAR ProSupport for Home, extend your warranty entitlement and support coverage further and get access to experts you trust. Protect your investment from the hassle of unexpected repairs and expenses. Connect with experienced NETGEAR experts who know your product the best. Resolve issues faster with 24/7 service.

Heritage shooting range frederick md.

Features. Accelerated Speed. Reliable Internet. Cost Savings. Equipped with one LAN Gigabit Ethernet Port, the NETGEAR CM600 supports speeds up to 960Mbps ‡ for streaming HD videos, faster downloads, and high-speed online gaming. Product Datasheet.To check this, wire connect a wired PC directly to port #1 on the CM modem. After it comes to ready, watch the networking status on your PC. It should change to the WAN IP address that your ISP gives out. Might contact your ISP and have them help you this this. Check the line quality up to the modem.With NETGEAR ProSupport for Home, extend your warranty entitlement and support coverage further and get access to experts you trust. Protect your investment from the hassle of unexpected repairs and expenses. Connect with experienced NETGEAR experts who know your product the best. Resolve issues faster with 24/7 service.Mar 17, 2019 · Hello Group, I am planning to upgrade my cable (Xfinity) modem, and eventually bump up to the gigabit plan. I have a question that I hope someone can answer. Will the netgear cm1000 (DOCSIS 3.1) ultra-high speed cable modem work okay with a slower (150mbp) plan, until i get switched over to the giga...

Disconnect the external router from the modem to isolate the issue. Be sure you don't have any coax cable line splitters in between the modem and ISP service box. Try testing with a different wired PC with the modem. Some older PCs can't handle speed testing near 900Mbps. You need a quad core PC to get good results.To connect a router to the cable modem: Wait for the Online LED to stop blinking and light solid green. Use an Ethernet cable to connect the Ethernet port on the cable modem to the WAN or Internet port on the router. Power on the router. Wait until the router is ready.When I plug the ethernet cord from the CM1000 to the wireless router, internet works fine. But sometimes we shut off the wifi (wireless router) in the house, so I just want to plug directly into the ethernet port on the CM1000 to my computers ethernet port. Frustratingly, none of my computers work when plugged directly into the CM1000 ethernet ...There is another none netgear cable modem that is used just for work and supplied by the same ISP and that modem never has a problem. Model: CM1000|Ultra-High Speed Cable Modem—DOCSIS® 3.1 Ready ... Current setup: CM2000-> RBE973S-> Trendnet TEG-S380-> GS716T-> pi-hole also in AP setup: RAXE500->EAX80 ... CM1000|Ultra-High Speed Cable Modem ...To set up an IPv6 Internet connection on your NETGEAR router: Launch a web browser from a device that is connected to your router's network. Enter www.routerlogin.net. A login window displays. Enter your user name and password. The default user name is admin.Get It By: Thursday, May 2. Free Shipping & Returns. This high speed DOCSIS ® 3.0 Cable Modem gives up to 1.4Gbps download speed for streaming HD videos, faster downloads and high speed gaming. Save money by avoiding rental fees. Certified with Xfinity with speeds up to 800Mbps, Spectrum service of 400Mbps, and with Cox service speeds of 500Mbps.blazing fast download speeds (up to 1 Gbps) meets DOCSIS 3.1 specifications and is backward compatible with DOCSIS 3.0. browser-based installation makes setup easy using a tablet, smartphone, or computer. handy on/off switch makes resetting your modem easier. Advanced Quality of Service (QoS) minimizes hiccups by prioritizing network traffic.Download this manual. High Speed Cable Modem. Mode l CM1000. Us e r Manual. September 2016. 202-11665-02. 350 East Plumeria Drive. San Jose, CA 95134. USA.Just wondering if anyone has upgraded their cm1000 to cm1200 modem. I recently made the switch but it's looking like cm1000 is more consistent and × We are aware of an issue affecting Nighthawk CAX30 Cable Modem Routers that may have resulted in an interruption of internet service.Set up Ethernet Port Aggregation. View the Ethernet Port Aggregation Status. ... NETGEAR CM1000 High Speed Cable Modem Manual (article) Modem NETGEAR CM600 User ManualWith NETGEAR ProSupport for Home, extend your warranty entitlement and support coverage further and get access to experts you trust. Protect your investment from the hassle of unexpected repairs and expenses. Connect with experienced NETGEAR experts who know your product the best. Resolve issues faster with 24/7 service.NETGEAR-Guest is for the 2.4 GHz WiFi band. NETGEAR-5G-Guest is for the 5 GHz WiFi band. Ensure that the Enable SSID Broadcast check box selected. Allowing the router to broadcast its WiFi network name (SSID) makes it easier to find your network and connect to it. If you clear this check box, you create a hidden network. Enter a guest …

The ethernet cable ran from the MOCA to the Eero Pro (acting as the router). The other ethernet cable ran from the Eero to the CM1000 (CM1000 only has 1 ethernet cable port). Result: Can connect to the Wifi network but not to the internet (Eero Pro light remains red). Now I know the CM1000 is not also a router so the Eero has to act as the router.

NETGEAR Cable Modem CM1000 - Compatible with All Cable Providers Including Xfinity by Comcast, Spectrum, Cox | for Cable Plans Up to 1 Gigabit | DOCSIS 3.1, Black (CM1000-1AZNAS) $194.00 & FREE Shipping. Details (8,404) Only 2 left in stock - order soon.Please post a copy and paste of the modems connection status page. <- done, upstream status light is green at the moment. Have the ISP check the signal and line quality UP to the modem. Be sure the ISP provisions the modem correctly. <- check. Be sure there are no coax cable line splitters in the between the modem and ISP service box. <- check.FURRYe38. Guru. 2020-02-02 01:47 PM. Have the ISP check the signal and line quality UP to the modem. Be sure there are not coax cable line splitters in the between the modem and ISP service box. Be sure your using good quality RG6 coax cable up to …The NETGEAR High Speed Cable Modem provides a connection to high-speed cable Internet with speeds up to 1 Gbps. 1 The cable modem is certified by all major cable Internet providers. A Gigabit Ethernet port provides fast access and downloads. The cable modem supports the assignment of IPv4 and IPv6 addresses by cable Internet providers.For more information visit the NETGEAR Press Room. ... I need to have a DOCSIS 3.1 router. As such, I have tried to install a CM1000 modem alongside my Orbi CBR40 but am having trouble getting them to work together. I currently have the modem connected to the Orbi and an Ethernet cable coming from the Orbi to my laptop which provides Internet ...This is to be expected. Keep the WiFi connection. Launch a web browser and enter mywifiext.net or 192.168.1.250. The New Extender Setup page displays. Click or tap NEW EXTENDER SETUP. If prompted to accept terms and conditions, click or tap YES or I AGREE. Choose your extender's admin credentials.Buy NETGEAR Nighthawk Cable Modem CM1200 - Compatible with all Cable Providers ... Power surges covered from day one. Real experts are available 24/7 to help with set-up, connectivity issues, troubleshooting and much more. ... (32x8) DOCSIS 3.1 | for XFINITY by Comcast, Cox. Compatible with Gig-Speed from Xfinity - CM1000-1AZNAS (Renewed) (3172 NETGEAR MODEM SUPPORTED SPEED TIERS DOCSIS® 3.1 Multi-Gig Internet CM1000 DOCSIS ® 3.1 Up to 1Gbps CM700 DOCSIS ® 3.0 32x8 Up to 400Mbps DOCSIS ® 3.0 16x4 Up to 200Mbps CM1200 CM500 DOCSIS® 3.1 Multi-Gig 1Gbps+ ® Multi-Gig 2.5Gbps CM1000 DOCSIS 3.1 Up to 1Gbps CM700 32x8 Up to 400Mbps DOCSIS 3.0 16x4 Up to 300Mbps CM2000 CM1200 This is the differences. cm1000v2-version 2. 100nas- version 1. 1znas- version 1 differnet box that made packaging/opening easier. cm1000-version 1. I've got both cm1000v1 and cm1000v2 and they function exactly the same for me. I'm on xfinity though. No clue how they'd work for spectrum since i haven't used them.FURRYe38. Guru. 2020-02-02 01:47 PM. Have the ISP check the signal and line quality UP to the modem. Be sure there are not coax cable line splitters in the between the modem and ISP service box. Be sure your using good quality RG6 coax cable up to the modem.

Line of moving lights in the sky.

How many questions is the servsafe manager test.

Jul 2, 2020 · Couple of factors are signal from ISP service to modem needs to be checked. Be sure to use good quality RG6 coax cabling. Be sure that no coax cable line splitters are in use. Other problems may stem from faulty wifi routers or bad configurations of the routers. The CM1000 is capable of handling 1Gb ISP services. gllong21620. Tutor. 2021-06-11 04:19 PM. Hello all, my setup of R7000 with CM1000 and EX6400v2. Several times a day, the router losing connection with the modem. The issue does not seem to be an ISP issue as service to modem is in place even as router drops out. i have rest the router via Nighhawk app. I change connection cable between modem ...Can I connect it to my EAX20 AX18000 Mesh Extender? I thought that I could and it was working for a bit but now I can't connect it at all. Yes I've done ass resets and whatnot. But I'm wondering, did I get an Extender that is not compatible with my Cable Modem Router? THANK YOU! Message 1 of 1. Ditto This.When connected to the Netgear cm1000, download speeds are at 400 mps or better. When connected to the Netgear ac1750, download speed is about 200 mps or lower. Current setup: CM2000-> RBKE963B-> Trendnet TEG-S380-> GS716T-> pi-hole. also in AP setup: RAXE500->EAX80.Factory reset the router and power it off. Power ON the ISP modem and let it sync. Then power ON the router and walk thru the setup wizard again using a wired PC and a web browser. @NG27 wrote: copy, well as i stated, my ISP came out and verified speeds on the line, everything checked out on their end.The CM1000 is a new DOCSIS 3.1 modem that was released recently. I noticed the CM1000 was added to list of modems impacted by this old security ... The list on right isn't inclusive of all of netgear's cable modems either. Either way, its confusing which products are impacted and what firmware version contains the fix. I shouldn't have to open ...Oct 28, 2017 · NETGEAR Expert. 2017-10-30 10:29 AM. Very quick and simple question. Is it absolutely necessary to hook the modem up to a computer during install? >> Not necessarily. if you do use your Routers WIFI, Please make sure you let router obtain its own DNS servers rather then trying to hard code it to Google's DNS servers (as some users do it). Sure. connect your router to it. Or call your isp and have them provision it over the phone and then connect it to a router.Apr 19, 2020 ... However I'd like to spread workload across Orbi WiFi and Netgear router like our old setup. Bought new CM1000 modem for more bandwidth to ...Trying to setup a network with a CM1000 on Xfinity. I live in a 1930 House with plaster walls so Wifi barely bleeds from room to room. I ran CAT6 from basement to attic patch panel thendrops into each bedroom closet. My network starts out like this: ... 6 Netgear Wireless Routers (3 x AC1200's, 1 AC1600, 2 x Nighthawk AC1900's) all set as ...The BASIC Home page displays. Select ADVANCED > Setup > LAN Setup. Make sure that the Use Router as DHCP Server check box is selected. Specify the range of IP addresses that the cable modem router assigns: In the Starting IP Address field, type the lowest number in the range. This IP address must be in the same subnet as the cable modem router. ….

CM1000 Installation/Setup Question Hello everyone! New to the community and couldn’t find the search topic field. Apologies if this has been answered previously. ... NETGEAR Expert Mark as New; Bookmark; Subscribe; Subscribe to RSS Feed; Permalink; Print; Report Inappropriate Content ‎2017-10-30 10:29 AM ‎2017-10-30 10:29 AM.NetgearNETGEAR CM1000 Manuals. Manuals and User Guides for NETGEAR CM1000. We have 5 NETGEAR CM1000 manuals available for free PDF download: User Manual, Troubleshooting Steps, Quick Start.Features. Next-Generation DOCSIS 3.1. Get support for up to 2.5 times faster internet speeds and 10 times faster download speeds than the first-generation DOCSIS 3.0 modem. Multi-Gig Internet. The newest generation of cable modems deliver up to 2.5 Gbps multi-gig internet. Ready for the Fastest Speeds.To connect a router to the cable modem: Wait for the Online LED to stop blinking and light solid green. Use an Ethernet cable to connect LAN port 1 on the cable modem to the WAN or Internet port on the router. Power on the router. Wait until the router is ready. Connect a computer to the router.CnR Reviews. 977 subscribers. Subscribed. 135. 24K views 4 years ago. Unboxing and how to connect of the CM1000 Netgear modem. You can support our channel for free by using the link below to...If you log into the cm1000, get a screen snip of the cable connections page and the event logs. Those help us check the signal and if its getting a signal. Current setup: CM2000-> RBE973S-> Trendnet TEG-S380-> GS716T-> pi-hole. also in AP setup: RAXE500->EAX80. 1.4gig download/100mbps upload from Xfinity.Learn more about the NETGEAR Nighthawk X10 and S8000 here: http://bit.ly/2aQXlVdWatch this quick video to learn how to setup link aggregation on the NETGEAR ...Connect the power adapter provided in the package to the cable modem and plug the power adapter into an electrical outlet. When the startup procedure is completed, the Power LED lights green . Wait for the cable modem to come online. It takes at least 10 minutes for the cable modem to come online on the network. Netgear cm1000 setup, MoCA, as its acronym suggests, is a substitute for. Ethernet, using (existing) co-axial cable. A cable modem already has a. co-ax port for communication with the ISP, and an Ethernet port for. communication with a router. MoCA is normally used between a router and. client devices, not between a modem and anything., Jan 23, 2020 ... ... Cm1000 modem and Orbi router with a single satellite package around 7 months ago. Setup was a breeze and it has been working fantastically ..., Guru. 2021-03-06 05:19 PM. The modem only has a few limited user features. Disable LAG on the modem. ALL other configurations and signals UP to the modem are handled by the ISP. Have the ISP check the signal and line quality UP to the modem. Be sure the ISP provisions the modem correctly. This is there responsbility., Hello everyone, I recently purchased a Netgear CM1000 cable modem to pair with my Comcast Xfinity gigabit internet service. However, I am having trouble with the modem. Here's what the LED's show when I plug it in and turn it on: The ethernet light stays on solid amber. Every other light slowl..., is the netgear cm1000 modem compatable with netgear nighthawk ac4000 tri-band wifi router? I am changing internet service and I am going to supply my own DOCSIS 3.1 Modem and I have a new Nighthawk AC4000 TRI-BAND WIFI Router still in box., NETGEAR CM1000-1AZNAS Gigabit 32x8 DOCSIS 3.1 Cable Modem Review - https://amzn.to/2AEEbPHThe CM1000 Ultra-High Speed Cable Modem, with speeds up to 1Gbps an..., I've had them activate my modem over the phone without anything being connected. Once its activated, then you could attach a router to it and reboot the modem and then the router. I guess it just depends on your isp., Make sure that the cable is tightly connected. Connect the power adapter. Connect the power adapter to the cable modem and plug the power adapter into an electrical outlet. When the startup procedure is complete, the Power LED lights green. If the Power LED does not light, press the Power On/Of button. Cable wall outlet., May 31, 2017 · Image 1 of 4. The Netgear CM1000’s back panel has a power button and a reset button. The triangle-shaped vents help keep the Netgear CM1000 from overheating. The Netgear CM1000’s five small LED status icons may be hard to read from across a large room. This Netgear modem is ready to deliver the future of fast internet. , Please post a copy and paste of the modems connection status page. Have the ISP check the signal and line quality UP to the modem. Be sure the ISP provisions the modem correctly. Be sure there are no coax cable line splitters in the between the modem and ISP service box. Be sure your using good quality RG6 coax cable up to the modem., Then use the NG router in router mode. You'll need to contact the ISP for help and information in regards to the modem being bridged correctly. 2. If you can't bridge the modem, disable ALL wifi radios on the modem, configure the modems DMZ/ExposedHost or IP Pass-Through for the IP address the NG router gets from the modem. https://kb.netgear ..., Jan 23, 2020 ... ... Cm1000 modem and Orbi router with a single satellite package around 7 months ago. Setup was a breeze and it has been working fantastically ..., Get it by Thu, Jul 13 - Fri, Jul 14 from Gastonia, North Carolina. • New condition. • 30 day returns - Free returns. MPN / Model# CM1000. Model/Series Ultra-High Speed Cable Modem. First Data FD5 Dual Com Credit Card Machine, 160Mb, Internet, Ethernet/Dial -NE. PICK UP OPTION., If you log into the cm1000, get a screen snip of the cable connections page and the event logs. Those help us check the signal and if its getting a signal. Current setup: CM2000-> RBE973S-> Trendnet TEG-S380-> GS716T-> pi-hole. also in AP setup: RAXE500->EAX80. 1.4gig download/100mbps upload from Xfinity., Wait for XFINITY to confirm that your cable modem is active. If the cable modem is not visible, XFINITY can give you instructions to verify why the cable modem does not connect with your high-speed Internet service. If the cable modem is visible to XFINITY, reboot the cable modem. Check your online status again., The BASIC Home page displays. Select ADVANCED. The Cable Information pane displays. Click the Factory reset button. A confirmation message displays. Click the OK button. The configuration is reset to factory default settings. When the reset is complete, the cable modem reboots. This process takes about one minute., With NETGEAR’s round-the-clock premium support, help is just a phone call away. Enter 192.168.100.1 into your browser address bar, then enter the modem login credentials. Typically, the user name is admin and the default password is password., This is the differences. cm1000v2-version 2. 100nas- version 1. 1znas- version 1 differnet box that made packaging/opening easier. cm1000-version 1. I've got both cm1000v1 and cm1000v2 and they function exactly the same for me. I'm on xfinity though. No clue how they'd work for spectrum since i haven't used them., Current setup: CM2000-> RBKE963B-> Trendnet TEG-S380-> GS716T-> pi-hole also in AP setup: RAXE500->EAX80 1.4gig download/50mbps upload from Xfinity We're members of the public helping out on our own time., is the netgear cm1000 modem compatable with netgear nighthawk ac4000 tri-band wifi router? I am changing internet service and I am going to supply my own DOCSIS 3.1 Modem and I have a new Nighthawk AC4000 TRI-BAND WIFI Router still in box., Current setup: CM2000-> RBKE963B-> Trendnet TEG-S380-> GS716T-> pi-hole also in AP setup: RAXE500->EAX80 1.4gig download/50mbps upload from Xfinity We're members of the public helping out on our own time., I'm currently running a Cox gigabit connection on a CM1000 modem using an Eero mesh network as my router. I am also subscribed to Eero+ and use their enhanced security to send all my DNS requests to Zscaler. Firmware is the latest approved from Cox network (3.01.04).Over the past two to three weeks ..., Here is the Config: Internet->CM1000->USG 3P->Laptop. DHCP is running only on the USG since the CM1000 does not have DHCP. LAN is setup as 192.168.1.X with the USG at 192.168.1.1. I can ping the 192.168.100.2 from the laptop. I cannot ping out onto the internet or even to the CM1000 at the 192.168.100.1 address., NETGEAR-Guest is for the 2.4 GHz WiFi band. NETGEAR-5G-Guest is for the 5 GHz WiFi band. Ensure that the Enable SSID Broadcast check box selected. Allowing the router to broadcast its WiFi network name (SSID) makes it easier to find your network and connect to it. If you clear this check box, you create a hidden network. Enter a guest …, Guru. 2021-03-06 05:19 PM. The modem only has a few limited user features. Disable LAG on the modem. ALL other configurations and signals UP to the modem are handled by the ISP. Have the ISP check the signal and line quality UP to the modem. Be sure the ISP provisions the modem correctly. This is there responsbility., The Netgear CM1000 has the following ports available on the back of the modem. Reset Button - Use this button if you want to restore the default factory settings. This button is recessed to prevent accidental resets of your modem. Coaxial Cable Connector (Cable / Internet - Connect your cable line to this port., After about a year of use, my CM1000 went dead. When I plug in the modem to power, all the lights blink once, and then the orange ethernet light stays on solidly. I've tried factory reset button, but the modem is not responding. It seems others have had this issue, but I did not see how they were resolved. If anyone has a resolution, please let ..., gllong21620. Tutor. 2021-06-11 04:19 PM. Hello all, my setup of R7000 with CM1000 and EX6400v2. Several times a day, the router losing connection with the modem. The issue does not seem to be an ISP issue as service to modem is in place even as router drops out. i have rest the router via Nighhawk app. I change connection cable between modem ..., If you log into the cm1000, get a screen snip of the cable connections page and the event logs. Those help us check the signal and if its getting a signal. Current setup: CM2000-> RBE973S-> Trendnet TEG-S380-> GS716T-> pi-hole. also in AP setup: RAXE500->EAX80. 1.4gig download/100mbps upload from Xfinity., Problem: My CM1000 modem will not pass internet to an RAX80 router. I tried connecting on a different RAX80 and got the same result. However the CM1000 will pass internet to a laptop via ethernet. What I've tried: Power cycling, factory reset. Screenshot: I attached a screenshot of the NETGEAR genie Cable Connection page for the CM1000. I don't ..., If you must share the connection, use a 3.5dB (1 to 2) splitter. 3. Connect the power adapter. Connect the power adapter to the cable modem and plug the power adapter into an electrical outlet. The cable modem might reset multiple times when you power it on. 4. Wait for the Online LED to light solid green., options in will be in router. we dont support 3rd party routers but you may want to look at below link on how to enable IPv6 on Google WIFI, Current setup: CM2000-> RBKE963B-> Trendnet TEG-S380-> GS716T-> pi-hole also in AP setup: RAXE500->EAX80 1.4gig download/50mbps upload from Xfinity We're members of the public helping out on our own time.